How to wire a GFCI outlet

icsparks

Community Member
View Badges
Joined
Dec 1, 2013
Messages
51
Reaction score
4
Location
West Virginia
Rating - 0%
0   0   0
Not point blank no, pretty much just got the "it doesn't work because that outlet is one" response and didn't want to sound like an idiot. I do recall him saying it should work as one but I wasn't exactly clear how so that combined with this post makes me feel like it is downstream and will act as one.

Thanks

You can wire GFCI outlets down stream in a circuit but remember that if the load side of the outlet is used to feed the other outlets down stream then the first outlet that trips will kill all power to the remaining down stream outlets in the circuit. If you wire to the line side of the outlet on all of the down stream outlets then each one will be a stand alone and not trip down stream. If wired correctly the tank outlet should work no matter how it was wired upstream. push the test button on the tank outlet and it should trip. If it doesnt then you need to find another electrician because he hooked up the wire on the load side of the outlet at the tank. If you push the test button on the upstream outlet then both outlets should be dead.
 

Spendley

Active Member
View Badges
Joined
Aug 8, 2013
Messages
199
Reaction score
1
Location
Maryland
Rating - 0%
0   0   0
So if my outlet is a regular outlet and does not have the reset switches, the electrician was an idiot and didn't know what he was talking about?

Full disclosure- I am also an idiot when it comes to these things :)
 

Zacco

Active Member
View Badges
Joined
Feb 2, 2014
Messages
397
Reaction score
45
Location
Pennsylvania
Rating - 0%
0   0   0
Spendly. You can protect up to 10 outlets down stream of a GFI. Connected to "load" side of the actual GFI outlet. NEC code. Allow 1.8 volt amps per outlet. The outlet that your electrician pointed out is probably protect from a GFI upstream. To test the outlet in question trip the GFI's in the basement. If the outlet in question goes out or loses power and is protected by the GFI.
 

Greg Chapman

New Member
View Badges
Joined
Dec 10, 2016
Messages
5
Reaction score
1
Location
Redmond, WA
Rating - 0%
0   0   0
Just tried to self install a GFCI myself -- and all appearances things looked ok until I switched on the room lights (same circuit). GFCI popped. I rechecked my work -- looked fine.... so instead of burning down the house called an electrician.

Turns out two room lights down stream were the culprit. They were first-flight LED bulbs from Phillips, about 4 years old. The electrician said he sees this all the time with LED bulbs of this age. I swapped out for newer bulbs, and things worked perfectly.

Just something to watch out for if you do it yourself.
 

Captain Jack

Community Member
View Badges
Joined
Feb 13, 2017
Messages
59
Reaction score
32
Location
Minnesota
Rating - 0%
0   0   0
I hate gfcis, they are verrrrry picky. You cant just piggy back a wire on the load side, you NEED a line and load. IE, if the outlet goes out, anything on the line end also goes out. It will not turn on unless it is wired that way.
You can splice the wires first and then pigtail power to the GFCI, that way the splice still sends power to whatever is wired and the GFCI will not affect the power to it.
 

fabutahoun

Angels and Acros
View Badges
Joined
Sep 18, 2015
Messages
2,702
Reaction score
14,610
Location
Amman Jordan
Rating - 0%
0   0   0
I got This one , Is it Any good?
It is hooked up to my tank since October 2016

https://www.amazon.com/gp/product/B00UOU6OVU/ref=oh_aui_search_detailpage?ie=UTF8&psc=1

upload_2017-3-5_14-32-0.png
 

jason2459

Not a paid scientist
View Badges
Joined
Jul 28, 2015
Messages
4,668
Reaction score
3,197
Rating - 0%
0   0   0
Great thread. I like redundancy and as much protection against equipment failures as possible. Things like Heaters and power strips in our hobby have created more havoc then necessary with the occasional fun dip of lights into the tank...

My standard Copy/paste on this topic:

I would also suggest a CACFI along with GFCI

CAFCI will help protect your house from fire
GFCI will help protect you from electrocution

00decdb99afb5c82c4057529171e2b6e.jpg


681a4d90b06f2d1ef97c14e6e5c6a23d.jpg



And a good surge protector will help protect your equipment.

Individual one shown above. Tripplite makes some good ones. Be warned some newer surge protection devices will stop power from flowing all together once it can no longer provide surge protection. This is actually a good thing IMO for many things like computers/tv/etc but NOT a good thing, again IMO, for many other things like refrigerators, freezers, our aquariums, etc. Some will make an audible alarm when exhausted which is nice too.

Plus a whole home. None last forever and will need replaced eventually based on how many surges and intensity of surges they've been hit by. Surges can come from outside your home, not just lightening strikes, and from inside the home.

Eaton Ultra and SquareD hepd80 are a couple good whole home surge protectors.
bf6fbd03b4b04f1ed0673892ebef727a.jpg



Plus having more then one circuit with life support spread across them. I have two additional circuits then what's pictured above to my main tank on the first floor with GFCI at the receptacles so its easier to reset them if tripped. Then the two shown in the picture above go to my basement sump with the GFCI at the breaker. Along with being a CAFCI. There are also AFCI breakers but don't protect against as many arc faults as a CAFCI.

And don't get confused by combination AFCI (CAFCI). That doesn't mean it combines GFCI with it. The packaging has to specify GFCI as well to support both CAFCI and GFCI. Sometimes called dual.


bd9ca223039632f97a210b17a4d007cc.jpg


Here's some visuals
af1e646bbcd39537132518af8119a231.jpg


89fcf62bdae99cee50bc1b93a4dc549f.jpg


And CAFCI protects against both of these where AFCI only parallel
537ac3cec3c96f97aa2b3b6a4ef6abeb.jpg


In the US the NEC will typically require a class A GFCI protection in places like a bathroom (fishtank) which trips at 6mA. Some places like commercial applications can use class C, D, or E that trip at 20mA.

http://m.csemag.com/index.php?id=9575&tx_ttnews[tt_news]=102229&cHash=89c8746cdc4a7fd8a3cb93f1d51ba57a
 
Last edited:

Dr RBG

Active Member
View Badges
Joined
Feb 15, 2017
Messages
253
Reaction score
177
Location
New England
Rating - 0%
0   0   0
You can also have a GFI breaker put in the breaker box. Does the whole circuit with one device. Need an electrician to do it but why burn down your house for a few bucks. :eek:
 

Huff747

Valuable Member
View Badges
Joined
Jul 18, 2017
Messages
1,181
Reaction score
1,028
Location
Glen Carbon, IL
Rating - 100%
2   0   0
I went to replace one of my outlets in my home office and when I opened it up (after breaker was off) and I found this. 2 wires coming into th box with white, black, red, ground. And the tab has been removed which I think would make this a switched receptacle except we've lived in the house for ~4 years and this outlet is not tied to any switch, both outlets have always been on. The only 2 switches in the room are for the light and ceiling fan. Can I just remove the red wire from the wirenut to the receptacle, leave the wirenut on the pair of red wires coming in and wire the outlet with just the black, white and ground?

Thanks for any info

IMG_4113.JPG
IMG_4111.JPG
 

Brew12

Electrical Gru
View Badges
Joined
Aug 14, 2016
Messages
22,488
Reaction score
61,061
Location
Decatur, AL
Rating - 0%
0   0   0
I went to replace one of my outlets in my home office and when I opened it up (after breaker was off) and I found this. 2 wires coming into th box with white, black, red, ground. And the tab has been removed which I think would make this a switched receptacle except we've lived in the house for ~4 years and this outlet is not tied to any switch, both outlets have always been on. The only 2 switches in the room are for the light and ceiling fan. Can I just remove the red wire from the wirenut to the receptacle, leave the wirenut on the pair of red wires coming in and wire the outlet with just the black, white and ground?

Thanks for any info

IMG_4113.JPG
IMG_4111.JPG
You are correct, that looks like it is wired as a half hot switched receptacle.

Without knowing where the other ends of each wire go it is hard to say for sure. Unfortunately, I can only see the wiring in 3 of the 4 wire nuts. You have one for the Reds, Whites, and grounds. I'm guessing the 4th one is for the Blacks.

The issue I see is that in a half hot switched receptacle, the reds should not be tied together. Normally the feed cable will use the neutral and black. On the cable to the switch, the black is tied to the feed cable and the red is tied to the switch receptacle. The black and red from this cable are then connected to the switch.

While it is possible that the installer had other intentions in mind, such as having each receptacle on separate circuits, I can't confirm that and it definitely isn't how I would recommend doing it. It does make me say that you should be very careful in there since it may be fed by two breakers, one with power on the red the other on the black.

I would make a concerted effort to determine where each end of that cable go and try to determine the installers intent. Sorry I can't be of more help!
 

Brew12

Electrical Gru
View Badges
Joined
Aug 14, 2016
Messages
22,488
Reaction score
61,061
Location
Decatur, AL
Rating - 0%
0   0   0
I went to replace one of my outlets in my home office and when I opened it up (after breaker was off) and I found this. 2 wires coming into th box with white, black, red, ground. And the tab has been removed which I think would make this a switched receptacle except we've lived in the house for ~4 years and this outlet is not tied to any switch, both outlets have always been on. The only 2 switches in the room are for the light and ceiling fan. Can I just remove the red wire from the wirenut to the receptacle, leave the wirenut on the pair of red wires coming in and wire the outlet with just the black, white and ground?

Thanks for any info

IMG_4113.JPG
IMG_4111.JPG
Let's bring in @Paul B and @Ramasule since they have more residential experience. I'm an industrial guy so they may prove to be more helpful.
 
Back
Top