Plumbing basement filtration room with flex pvc

OP
OP
Ironwill723

Ironwill723

Well-Known Member
View Badges
Joined
Apr 25, 2009
Messages
658
Reaction score
390
Rating - 100%
1   0   0
Did you end up making a decision.. I bought rigid and the flex, going to do a combo as well.
Sorry for the delayed response...but to answer your question...no I have not made a decision yet. Still working on finishing my diy stand. I will probably end up using some combination of the two especially the part that passes between my first floor and into the basement filtration room.
 

WhatCouldGoWrong71

Valuable Member
View Badges
Joined
May 19, 2023
Messages
1,475
Reaction score
882
Location
Memphis
Rating - 100%
3   0   0
I picked up some yesterday at Lowe’s. I need to add it for a 2 foot section on my mixing station that needed some work. Super flex, so much so I am going to fix one other section. However, I’m not concerned with my mixing station looking sexy, I just want it to be a well functioning tool. This stuff, when used with other hard PVC, looks like a floppy noodle. Compared to all the other dead straight lines, this creates an eye sore for me. No way I could use it where I have “public” facing plumbing. I would absolutely use it for plumbing work that only I would see.
 

Pntbll687

Valuable Member
View Badges
Joined
Oct 4, 2017
Messages
2,188
Reaction score
2,721
Rating - 0%
0   0   0
I'll throw another option out there. Heat up and bend the pvc for some nice curves in the piping.

Here's a video on it. This is Thomas from BRS from way before his time at BRS, some really good info.

 

Dburr1014

10K Club member
View Badges
Joined
May 8, 2016
Messages
11,300
Reaction score
10,981
Location
CT
Rating - 0%
0   0   0
I'll throw another option out there. Heat up and bend the pvc for some nice curves in the piping.

Here's a video on it. This is Thomas from BRS from way before his time at BRS, some really good info.

Good video.
I used a torch to do some bends on my other tank 10 years ago. Just need to move the torch like the video explains.
One thing I noticed at the bends, I was dismantling the old pipe and those bends are brittle after 10 years. Instead of cutting they shattered under the pvc cutters.
Just worth noting.
 

GlassMunky

2500 Club Member
View Badges
Joined
Jan 30, 2014
Messages
3,326
Reaction score
4,409
Location
NJ-Philly Burbs
Rating - 0%
0   0   0
I'll throw another option out there. Heat up and bend the pvc for some nice curves in the piping.

Here's a video on it. This is Thomas from BRS from way before his time at BRS, some really good info.

This is going to seriously reduce the lifespan of the tubing where it’s bent. It’s not designed to be twisted like that making the walls thinner and therefore able to handle less pressure.
Probably not worth it in the end IMO.
 

Dburr1014

10K Club member
View Badges
Joined
May 8, 2016
Messages
11,300
Reaction score
10,981
Location
CT
Rating - 0%
0   0   0
There is really no pressure on aquarium plumbing.
I can't think of any dead-heading that would be done, not like house plumbing where you shut off valves in your bathroom/kitchen.
 

GlassMunky

2500 Club Member
View Badges
Joined
Jan 30, 2014
Messages
3,326
Reaction score
4,409
Location
NJ-Philly Burbs
Rating - 0%
0   0   0
There is really no pressure on aquarium plumbing.
I can't think of any dead-heading that would be done, not like house plumbing where you shut off valves in your bathroom/kitchen.
You said it yourself though, when you moved stuff the bends broke meaning they were the weakest points in the system.

I get that we don’t have what most people would call real “pressure” but the point still stands
 

Dburr1014

10K Club member
View Badges
Joined
May 8, 2016
Messages
11,300
Reaction score
10,981
Location
CT
Rating - 0%
0   0   0
You said it yourself though, when you moved stuff the bends broke meaning they were the weakest points in the system.

I get that we don’t have what most people would call real “pressure” but the point still stands
Well, no, I said *when dismantling* and *cutting* the pipe, it shattered. I was not just moving it. It was still very strong but you cannot cut it with pvc cutters or it might shatter and cut you.
Moving it you cannot tell any difference than regular pvc.

Bottom line; *in my opinion*, if I had to heat pipe to bend it for aquarium plumbing in the future, I would do so again without the worry of longevity of said pvc.
 

GlassMunky

2500 Club Member
View Badges
Joined
Jan 30, 2014
Messages
3,326
Reaction score
4,409
Location
NJ-Philly Burbs
Rating - 0%
0   0   0
I fully understand what you meant and what you were doing.

My opinion is just contrary to yours.
In MY opinion I would never recommend to anyone, that they heat and bend their pvc, because of the many issues that could come from it unless you are a pro. The average hobbyist especially newer reefers looking for plumbing info should stay far away from this as it’s super advanced.
Bend a little too far and now it’s too thin on the outer edge of the bend leading to lesser lifespan or maybe you heated up the area for just a little too long and it got a little too hot and you end up making a tiny hole or something.
So many things to go wrong.

Sure it can be done and sure it’ll work but I really don’t think most people should do this unless you have no other options.

Again just opinions
 

GlassMunky

2500 Club Member
View Badges
Joined
Jan 30, 2014
Messages
3,326
Reaction score
4,409
Location
NJ-Philly Burbs
Rating - 0%
0   0   0
Lightly heating up flex pvc so it bends easier and bending rigid pvc are 2 totally different things in my mind
 

GlassMunky

2500 Club Member
View Badges
Joined
Jan 30, 2014
Messages
3,326
Reaction score
4,409
Location
NJ-Philly Burbs
Rating - 0%
0   0   0
How much pressure is there on aquarium plumbing?
It’s not about the actual amount of pressure

Let’s say the the pressure is whatever rating you want to say, it doesn’t matter.

If most of the tubings wall is say 2mm thick and then you bend it and make that wall 1mm thick due to the stretching that wall can now handle half of what it used to be able to.

Make sense?
 

GlassMunky

2500 Club Member
View Badges
Joined
Jan 30, 2014
Messages
3,326
Reaction score
4,409
Location
NJ-Philly Burbs
Rating - 0%
0   0   0
Formufit Colored PVC 1" pipe is only 3.38 millimeters thick

I would have thought it were thicker

It's like schedule 30 pipe, 28
Yes that colored stuff is real thin which is why bending it concerns me and why I personally wouldn’t do it.

But people are free to do whatever they want to on their systems
 

Zissou Intern

Community Member
View Badges
Joined
Nov 15, 2023
Messages
45
Reaction score
35
Location
Northeastern PA
Rating - 100%
1   0   0
I used flex PVC because I wanted to eliminate as many angled fittings as possible. I think it turned out really nice. It is true that the pipe has a natural curve it wants to maintain, but I incorporated that into my design. For your case, I imagine you could use some pipe clamps to keep things under control between floors. I’ll drop a few pics below but there are more in my build thread.
 

Attachments

  • IMG_9644.jpeg
    IMG_9644.jpeg
    115.6 KB · Views: 26
  • IMG_9645.jpeg
    IMG_9645.jpeg
    277 KB · Views: 29

Pntbll687

Valuable Member
View Badges
Joined
Oct 4, 2017
Messages
2,188
Reaction score
2,721
Rating - 0%
0   0   0
Good video.
I used a torch to do some bends on my other tank 10 years ago. Just need to move the torch like the video explains.
One thing I noticed at the bends, I was dismantling the old pipe and those bends are brittle after 10 years. Instead of cutting they shattered under the pvc cutters.
Just worth noting.
I think this has to do more with the saltwater than the bending. I re plumbed my tank and had the same happen to perfectly straight pipe. Also had pvc pipe shatter that had been used for frag rack legs for just over a year.
 

HAVE YOU EVER KEPT A RARE/UNCOMMON FISH, CORAL, OR INVERT? SHOW IT OFF IN THE THREAD!

  • Yes!

    Votes: 32 45.7%
  • Not yet, but I have one that I want to buy in mind!

    Votes: 9 12.9%
  • No.

    Votes: 26 37.1%
  • Other (please explain).

    Votes: 3 4.3%
Back
Top