jazzfisher
Well-Known Member
Yes, I’m using them. I like the higher level in the DT.
Innovative Marine Nuvo 30L Club/Index/Resource Thread
- AIO Build
- Thread starter ReeferReefer
- Start date
- Tagged users None
Zoajohn
Well-Known Member
Check out this page. Saxby is a popular one
Signature Series - AquaIllumination
www.aquaillumination.com
Check out this page. Saxby is a popular one
Signature Series - AquaIllumination
good for anemones?
where can i find AB+
Zoajohn
Well-Known Member
I run a gyre 1k in my 30L. Recently added sand and ooo boy it’s blowing. It’s the caribsea Fiji pink. Gyre on 10% still exposes glass in the middle. Does anyone run a gyre 1k with sand successfully?
i just got m 1k and i hate the programming i cant figure it out right now its on 10% steady and i cant figure anything else out. anything more than 10% oh boy
Zoajohn
Well-Known Member
What confuses you about it specifically? I can try to help you get it.
You click the “M” looking button bottom right of the controller until you see all mode icons flashing on the left. Then with the scroll wheel, select the mode you want with the middle button. Once you select a mode, you can adjust the power, the time length of power if using wave or pulse, whether you want reverse power flow (negative power percent) etc. once you are done make sure you are out of the mode settings, back to where all mode icons flash. Then click the M button again and you’re locked in.
mta_morrow
Of course I have room for 1 more fish!
I have done a lot of experiments with my 2 gyres. For that issue you can try a couple things.
1: lower the gyre and rotate the cages so the water starts hitting the surface about 1/2 way across the tank.
2: turn the gyre upside down and rotate the cages same as above.
My first tank was an IM30L and I absolutely loved it. Here is a pic just before my upgrade
Zoajohn
Well-Known Member
How do you rotate the cages? I always assumed my gyre flow was fixed. Since the magnetic mount is rubber and doesn’t adjust. I guess this would be on the front of the pump itself?I have done a lot of experiments with my 2 gyres. For that issue you can try a couple things.
1: lower the gyre and rotate the cages so the water starts hitting the surface about 1/2 way across the tank.
2: turn the gyre upside down and rotate the cages same as above.
My first tank was an IM30L and I absolutely loved it. Here is a pic just before my upgrade
mta_morrow
Of course I have room for 1 more fish!
I’m out and about right now or I would send pics. I will try to explain. I have the maxspect so I think they are similar. Power off and remove from tank. Act like you are disassembling for cleaning. The left and right cages should rotate. Rotated upwards 1/8 inch at a time then place back in the tank maybe 3-4” below water line
mta_morrow
Of course I have room for 1 more fish!
Don’t swap yet. I will help you. You may still want to change afterwards but I don’t think u will.
mta_morrow
Of course I have room for 1 more fish!
I did not have a gyre in my IM30L. I have 2 in my current tank. Here is a video watch and see some of the flow. Look at the corals on the bottom. The cespitularia bottom left, frogspawn bottom front, clam mantle, gsp bottom right. Nice gentle flow. All 4 cages on the 2 gyres aimed a little different as well as 1 gyre is about 11/2” below the water line and the other about 4”.
jazzfisher
Well-Known Member
Do you have 2 gyres on your 30 L? (not sure what you mean by current tank) I'm no expert on flow but I have the 1k gyre on one side of my 30L & 2 Current 660's on the other side. I find I can not put the gyre up past 10+ or 30- or I get too much flow.
Similar threads
- Price: 300.00
- Shipping NOT Available
- Price: 800
- Shipping NOT Available
Maryland Virginia Washington, D.C. Aquariums Package Deal Dry Goods
FS: Innovative Marine Nuvo Fusion 20 with Custom Stand & Ton o accesories
- Price: 550 obo
- Shipping NOT Available
