Return line mistake?

abrichy

New Member
View Badges
Joined
Dec 12, 2023
Messages
8
Reaction score
2
Location
Salt Lake City
Rating - 0%
0   0   0
I am so close to finishing the build of my 60g cube. I wanted to dip my toes in the sump and plumbing area, just for fun.
I think I made the mistake of doing a 1/2” return line, figured with not doing more than 400gph max, I would get away with it. Well, after doing a test on my pump I got, it is not strong enough (Sicce SDC 3.0 800gph, on full power I’m receiving about 180gph) and cannot deal with the head pressure; about 3ft vertical with one 90 degree turn.
I’m too inexperienced to make this call, should I just redrill for a 3/4” return, and get a stronger pump? Or is there a way to salvage this situation?
IMG_1782.jpeg
 

Magok

New Member
View Badges
Joined
Mar 15, 2023
Messages
17
Reaction score
4
Location
Greece
Rating - 0%
0   0   0
Sounds kinda narrow pipe for the gallons...
I would have gone for bigger diameter but unfortunately Im not experienced enough to tell you what needs to be done now.
 

Asm481

Active Member
View Badges
Joined
Jul 23, 2022
Messages
185
Reaction score
164
Location
Kenosha
Rating - 0%
0   0   0
I don't know how successful you will be drilling from a 3/4 bulkhead. Would worry about chipping it and losing the tank. I would run 3/4 inch up to the last elbow which could be a 3/4 x1/2 elbow. I would lose the backflow valve as that adds resistance and are ineffective as soon as any algae or slime builds in the line. To control backflow, you need to keep the return line close to the surface and siphon break hole on bottom of return line in the display tank.
 

RocketEngineer

Well-Known Member
View Badges
Joined
Sep 3, 2019
Messages
999
Reaction score
1,091
Rating - 0%
0   0   0
I second what Asm481 said:
1) Increase the plumbing to 3/4” right up to the bulkhead then adapt down at the bulkhead.
2) Remove the check valve. In our tanks, the biofilm grows on all surfaces, including on valve seats. All it takes is one bit of crud to cause the check valve to fail. No amount of cleaning can fix this flaw. Proper outlet placement is the best solution.

One other note: 180gph should be plenty for a 60g tank.
 

strich

Active Member
View Badges
Joined
Feb 28, 2024
Messages
316
Reaction score
458
Location
Queensland, Australia
Rating - 0%
0   0   0
I had no idea check values were so useless in reef tanks! I've seen heaps of youtube builds using them.
 

KrisReef

10K Club member
View Badges
Joined
May 15, 2018
Messages
15,227
Reaction score
31,279
Location
ADX Florence
Rating - 0%
0   0   0
Abandon the drilled return, plug it and add a new return, maybe even a 1” that goes over the top and then into the tank with a shallow surface spray to prevent siphon problems if the power goes out and gives you more flow capacity from the return pump.

If you do drill a larger hole put it higher up on the back wall and plug the 1/2” that is too low unless you have a huge sump to hold the water?
 

HAVE YOU EVER KEPT A RARE/UNCOMMON FISH, CORAL, OR INVERT? SHOW IT OFF IN THE THREAD!

  • Yes!

    Votes: 32 45.7%
  • Not yet, but I have one that I want to buy in mind!

    Votes: 9 12.9%
  • No.

    Votes: 26 37.1%
  • Other (please explain).

    Votes: 3 4.3%
Back
Top