GHL ProfiLux 4 Official Announcement

[fredro]

Can I calibrate using the touch screen?

Yes

 

[stevo01]

Programming Guide - Page 50 - Calibrating Senors. Page 53 - pH.

Does this look right? I set value 1 for 7 and value 2 for 9. With a tolerance of 1.

 

[stevo01]

I'm thinking the chart on the manual is showing the range but I should set the value for the numbers on the calibration fluids. Is this correct?

 

[d2mini]

Yes, 7&9 for saltwater.

 

[stevo01]

Thanks! The assistance has been awesome. Ill finish up theses probe calibrations and get some more pictures of the process.

 

[stevo01]

Calibration pictures.

 

[fredro]

Is there anywhere in myGHL or any other ProfiLux interface, that you can enter any other data? Like how Apex Fusion has a section to enter your Alk, Phosphate, Calcium and other reading you may want to log.

 

[stevo01]

Calibration of conductivity.

 

[stevo01]

I wasnt able to get to the pumps today.

I may have messed up my temp sensor, it's reading .8 degrees lower than my finnex heater controller probe. I did something in that probes settings in gcc that caused it to read lower I think. Is there any way to restore default setting for just the Temps probe?

 

[cbear44]

I wasnt able to get to the pumps today.

I may have messed up my temp sensor, it's reading .8 degrees lower than my finnex heater controller probe. I did something in that probes settings in gcc that caused it to read lower I think. Is there any way to restore default setting for just the Temps probe?

0.8C or 0.8F? Mine reads about 0.8F lower than my digital probe so hard to know what is right. I don't know how to calibrate the temp probe.

 

[stevo01]

Because I remember it was only .

0.8C or 0.8F? Mine reads about 0.8F lower than my digital probe so hard to know what is right. I don't know how to calibrate the temp probe.

0.8F here also. Both probes are close to each other.

 

[Lasse]

You should not calibrate it but you can set an offsett here if you have a sensor that you know is right.

​

Sincerely Lasse

 

[cbear44]

You should not calibrate it but you can set an offsett here if you have a sensor that you know is right.
Sincerely Lasse

What version of GCC are you running? What is totally odd is that in 1.0.9.4 I do not have buttons for "calibrate" or "Adjust temperature" that I can click on. When I click "Temperature 1" it will briefly appear as a "Virtual sensor" and then disappears once it registers my temp probe. I can probably do this in the P4 on screen menu

I'm fine with knowing that at a setting of 76.4 in the sump, my display tank is 77 based on my thermometer with +/- 2F variance that I've been using for my tank. I'm actually more apt to believe the P4 probe.

 

[M3ace9]

I set my unit up yesterday and the temp was off by .8 also. I woke up this morning and it was spot on.

 

[Martyd]

Hey guys. I got mine this morning, but I'm dead in the water. I can't even figure out how to change the language from German to English. Can someone help me? My cell is 443-910-4069.

Thanks.

Marty

 

[fredro]

Hey guys. I got mine this morning, but I'm dead in the water. I can't even figure out how to change the language from German to English. Can someone help me? My cell is 443-910-4069.

Thanks.

Marty

If you read back a few pages in a this thread, this issues is discussed. Good luck

 

[Lasse]

@cbear44 I´m running 1.0.9.2

@Martyd

Start GCC

Before you connect - click View up in the top

Chose language

Sioncerely Lasse

 

[Waboss]

Iiiiiitttttssssss heeeeeerrrrrree.............

And setup, configured and doing it's job!

Setup was a breeze. I spent more time calibrating probes and wiring/positioning it than configuring it.

 

[stevo01]

Iiiiiitttttssssss heeeeeerrrrrree.............

And setup, configured and doing it's job!

Setup was a breeze. I spent more time calibrating probes and wiring/positioning it than configuring it.

nice!

 

[glavaron]

Can someone please tell me how to configure outlets? I can manually turn them on but nothing beyond that. I am trying to program like Apex. Turn heater on set temperature. Turn off at another temperature. Cannot get 2.1 to power on unless I manually over ride the outlets