Ecotech flow

Billups

Community Member
View Badges
Joined
Jul 20, 2020
Messages
25
Reaction score
18
Location
Sanford
Rating - 0%
0   0   0
Fellow reefers,

Question about flow in your reef tank. I have a 90 gallon 2 feet by 3 feet and 2 feet tall tank with one ecotech MP40 and another MP10 on opposites sides of each other. In my first 30 gallon tank I found out I had to little flow. Now I think I have too much flow in my 90 when I am was using both MP40 and MP10 at 90% of their power. What would you recommend for my new 90 gallon tank that has an NSA rock work and 95% LPS with zoas being the other 10%? Tank is 6 months old and have plans to add SPS once the tank reaches its one year mark but I am curious what percentage of the pumps I should be using for my LPS dominate tank currently. Thank you!
 

watdachuck

Valuable Member
View Badges
Joined
May 21, 2013
Messages
1,028
Reaction score
989
Location
Columbus, OH
Rating - 0%
0   0   0
I would try this based on Ecotechs Flow Calculator. It is how I determined my flow speeds.

It looks like no greater than 60-70% on either pump.


A8D4350C-BF9B-4022-B5FA-ED4BD35B712F.png


A4862972-B76B-4CB9-8771-78816F0D4088.jpeg
 

rtparty

5000 Club Member
View Badges
Joined
Jan 19, 2010
Messages
5,388
Reaction score
9,137
Location
Utah
Rating - 100%
4   0   0
I have one MP60 (buying the 2nd soon) on my 250g peninsula and a Tunze Stream 3. I run the MP60 on lagoon mode at 100% and I definitely need the 2nd pump so I can remove the Stream 3.

Lots of variable when it comes to flow. The Ecotech calculator says I can run one MP60 on my tank and be good for SPS. Which is completely wrong.
 

Susan Edwards

5000 Club Member
View Badges
Joined
Nov 28, 2016
Messages
5,473
Reaction score
7,030
Location
Tracy, California
Rating - 0%
0   0   0
does this calculator take into consideration placement? I have 2 mp40's on the back wall directed toward front with 2 gyres on each end. Per the calculator I should be around 3300 for lps and 6000 for sps. I have a mixed reef. The mp's are running in the 33-3300 range currently. A lso, I don't want too much flow hitting the front glass in case over time that is too much pressure on glass? My only complaint with the mp's is I wish I could direct the flow--angle each in a bit toward the center.
 

watdachuck

Valuable Member
View Badges
Joined
May 21, 2013
Messages
1,028
Reaction score
989
Location
Columbus, OH
Rating - 0%
0   0   0
I have one MP60 (buying the 2nd soon) on my 250g peninsula and a Tunze Stream 3. I run the MP60 on lagoon mode at 100% and I definitely need the 2nd pump so I can remove the Stream 3.

Lots of variable when it comes to flow. The Ecotech calculator says I can run one MP60 on my tank and be good for SPS. Which is completely wrong.
I mean it’s wrong and it’s right. The total flow from one meets the target for total flow a tank needs. To your point you couldnt meet the the various flows around the tank to avoid dead spots or blasting corals to death.

I run a single MP60 on my 180 just fine.
 

watdachuck

Valuable Member
View Badges
Joined
May 21, 2013
Messages
1,028
Reaction score
989
Location
Columbus, OH
Rating - 0%
0   0   0
does this calculator take into consideration placement? I have 2 mp40's on the back wall directed toward front with 2 gyres on each end. Per the calculator I should be around 3300 for lps and 6000 for sps. I have a mixed reef. The mp's are running in the 33-3300 range currently. A lso, I don't want too much flow hitting the front glass in case over time that is too much pressure on glass? My only complaint with the mp's is I wish I could direct the flow--angle each in a bit toward the center.
IMO no, it’s just total flow targets based on coral type and tank size. There are lots of variables that can come into placement of the pumps and where coral are around them. Or open aqua scape versus tighter.
 

gbru316

Well-Known Member
View Badges
Joined
May 13, 2022
Messages
896
Reaction score
1,638
Location
Melbourne, FL
Rating - 0%
0   0   0
There is no such thing as too much flow but you can absolutely have too much velocity.

I can blow the tissue off an acropora with a 100 gph power head if I placed it directly in front of the nozzle. Place that same coral 24” from the same power head, and it’ll die from the inability to excrete waste products.

I’m considering 2 more tunze 6040’s to my 40 breeder, resulting in almost 120x turnover per hour. But because of the way they disperse the water, they’re much more gentle than the mp10 (which is roughly comparable in flow rate). The mp10 is like a laser beam in comparison (but still much better than the options we had prior to vortechs).
 
Last edited:

Susan Edwards

5000 Club Member
View Badges
Joined
Nov 28, 2016
Messages
5,473
Reaction score
7,030
Location
Tracy, California
Rating - 0%
0   0   0
IMO no, it’s just total flow targets based on coral type and tank size. There are lots of variables that can come into placement of the pumps and where coral are around them. Or open aqua scape versus tighter.
that's what I figured.
 

Lavey29

10K Club member
View Badges
Joined
Apr 29, 2021
Messages
13,117
Reaction score
14,356
Location
United States
Rating - 0%
0   0   0
I have basically the same size tank mixed reef with SPS and LPS. I have 2 MP40s. They run at 40% during the day in lagoon mode and 28% overnight.
 
Back
Top