What do you need 3d designed for Christmas? I'll make it for the community...

[kenchilada]

Here you go. The tube profile should match. I added 6 bolt locations that are threaded so you can secure the real to the tube. You could use t-nuts to insure this thing never moves. You can also secure the cable to one or many of the bolt locations. Last, the outer thread is 3mm and I was just guessing that the cable would be around that size. Let me know the diameter of the cable and I can update it.

View attachment 1948834

Wow that is amazing!! Thanks! I like the T-nut idea.

I sent a message to ATI asking about the cable specs. I’ll find my calipers tomorrow and check too.

 

[dumpysauce]

Here is the updated model. This should be pretty close to complete.

At the bottom, I added a hollow hexagon that can be glued to the bottom of the sterilizer with a magnet inside. This will make the sterilizer snap in place and prevent it from rotating. You can lift up the sterilizer and rotated 45 or 90 degrees then drop it back down into the hex slot.

Here is the Thingiverse link https://www.thingiverse.com/thing:4700825

View attachment 1948906View attachment 1948907View attachment 1948908

That's awesome! Thanks! I'll print it out today or tomorrow!
Do you have anywhere I can throw you a tip or anything? I'd call it a coffee fund, but more like coral frag fund haha

 

[kenchilada]

Here you go. The tube profile should match. I added 6 bolt locations that are threaded so you can secure the real to the tube. You could use t-nuts to insure this thing never moves. You can also secure the cable to one or many of the bolt locations. Last, the outer thread is 3mm and I was just guessing that the cable would be around that size. Let me know the diameter of the cable and I can update it.

View attachment 1948834

Cable is ~1.2mm. ATI says it is the same as bicycle derailleur cable.

 

[Bepis]

This might work for both? I need the measurement of the Tunze controller and the smart power strip. I also need a profile picture of the strip. The plan is to convert the light on the strip with a snap-on part that holds the Tunze controller.

View attachment 1946201

Sorry for the wait got caught up in the week

 

[Tastee]

Happy new year to you and a big thanks for the free assistance to fellow reefers you are providing.

 

[ocpondpoacher]

If this is still open, an anemone guard/wave maker cover for a Jebao SOW-4. And merry Christmas! sweet of you to have offered this to people!

I am not really sure how I would model this because I don't have a Jebao for reference. Plus the design of this wavemaker is circular and allows for directional adjustment. It is likely that I would have to make the 3 nem guard so that the flow direction is locked and pointing forward.

If you can shoot me over some references and a drawing of what you think it should look like please do.

 

[ocpondpoacher]

Cable is ~1.2mm. ATI says it is the same as bicycle derailleur cable.

Here is the link to the Thingiverse file. I think the 3mm threads will be the right size for the 1.2mm cable.

63mm Od Aluminum Rod Real by Ocpondpoacher

This part is designed to slip over a 63mm od aluminum pipe. The rod is connected to a motor which will allow it to spin and the threads will real up a 1.5mm cable.

www.thingiverse.com

 

[kenchilada]

Here is the link to the Thingiverse file. I think the 3mm threads will be the right size for the 1.2mm cable.

63mm Od Aluminum Rod Real by Ocpondpoacher

This part is designed to slip over a 63mm od aluminum pipe. The rod is connected to a motor which will allow it to spin and the threads will real up a 1.5mm cable.

www.thingiverse.com

Thanks, gonna track down someone that can print a couple of these! The tube motor arrives tomorrow.

 

[ocpondpoacher]

Thanks, gonna track down someone that can print a couple of these! The tube motor arrives tomorrow.

You need 2? DM me your address. I’ll print them out for you.