Randy Holmes-Farley
Reef Chemist
Staff member
Super Moderator
Excellence Award
Expert Contributor
Article Contributor
R2R Research
My Tank Thread
In a previous thread, I posted a true two part DIY recipe:
https://www.reef2reef.com/threads/new-diy-two-part-recipes-with-higher-ph-boost.344500/
But some folks may want to just swap the new ingredient into my 2/3 part recipe (as used by BRS, for example).
Here's the original recipe link (which has a lot more discussion on the details and rationale):
http://reefkeeping.com/issues/2006-02/rhf/index.php
The new recipe is shown below. It has about twice the pH boost of the original recipe (#1) and should be added to a very high flow area. Initial cloudiness (magnesium hydroxide) is expected, but it should disperse and dissolve. If not, stop using it and figure out why.
Alk part
Add 283 grams of sodium hydroxide to 1 gallon of fresh water. It will get quite warm. Make sure it doesn't soften your container. This solution will contain about 1,900 meq/L of alkalinity (5,300 dKH). BE CAREFUL WITH THIS SOLUTION: IT HAS A pH ABOVE 14. Do not get it in your eyes or on your skin. Keep all reef chemicals, especially this alk part, in a way that children cannot access them.
Calcium part
Dissolve 500 grams (about 2 ½ cups) of calcium chloride dihydrate (such as Dowflake 77-80% calcium chloride or ESV calcium chloride; see below for substitutes and sources) in enough water to make 1 gallon of total volume. You can dissolve it in about ½ gallon of water, and then pour that into the 1 gallon container and fill it to the top with more freshwater. This solution has about 37,000 ppm calcium.
Magnesium part
Dissolve Epsom salts (magnesium sulfate heptahydrate (3 cups) and magnesium chloride hexahydrate (5 cups) in enough purified freshwater to make 1 gallon total volume. There will likely be a precipitate that forms even if you fully dissolve both ingredients separately. That precipitate is calcium sulfate (calcium as an impurity in the magnesium chloride and sulfate from the Epsom salts). It is fine and appropriate to dose the precipitate along with the remainder of the fluid by shaking it up before dosing.
This solution is added much less frequently or in lower volume than the other two parts. Add 16% as much as the other two parts. Over the time you add 1 gallon of the others, 1 add 610 mL (2 ½ cups) of this solution. You can add it all at once or, preferably, over time as you choose, depending on the aquarium's size and set up. Add it to a high flow area, preferably a sump. In a very small aquarium, or one without a sump, I suggest adding it slowly.
https://www.reef2reef.com/threads/new-diy-two-part-recipes-with-higher-ph-boost.344500/
But some folks may want to just swap the new ingredient into my 2/3 part recipe (as used by BRS, for example).
Here's the original recipe link (which has a lot more discussion on the details and rationale):
http://reefkeeping.com/issues/2006-02/rhf/index.php
The new recipe is shown below. It has about twice the pH boost of the original recipe (#1) and should be added to a very high flow area. Initial cloudiness (magnesium hydroxide) is expected, but it should disperse and dissolve. If not, stop using it and figure out why.
Alk part
Add 283 grams of sodium hydroxide to 1 gallon of fresh water. It will get quite warm. Make sure it doesn't soften your container. This solution will contain about 1,900 meq/L of alkalinity (5,300 dKH). BE CAREFUL WITH THIS SOLUTION: IT HAS A pH ABOVE 14. Do not get it in your eyes or on your skin. Keep all reef chemicals, especially this alk part, in a way that children cannot access them.
Calcium part
Dissolve 500 grams (about 2 ½ cups) of calcium chloride dihydrate (such as Dowflake 77-80% calcium chloride or ESV calcium chloride; see below for substitutes and sources) in enough water to make 1 gallon of total volume. You can dissolve it in about ½ gallon of water, and then pour that into the 1 gallon container and fill it to the top with more freshwater. This solution has about 37,000 ppm calcium.
Magnesium part
Dissolve Epsom salts (magnesium sulfate heptahydrate (3 cups) and magnesium chloride hexahydrate (5 cups) in enough purified freshwater to make 1 gallon total volume. There will likely be a precipitate that forms even if you fully dissolve both ingredients separately. That precipitate is calcium sulfate (calcium as an impurity in the magnesium chloride and sulfate from the Epsom salts). It is fine and appropriate to dose the precipitate along with the remainder of the fluid by shaking it up before dosing.
This solution is added much less frequently or in lower volume than the other two parts. Add 16% as much as the other two parts. Over the time you add 1 gallon of the others, 1 add 610 mL (2 ½ cups) of this solution. You can add it all at once or, preferably, over time as you choose, depending on the aquarium's size and set up. Add it to a high flow area, preferably a sump. In a very small aquarium, or one without a sump, I suggest adding it slowly.
Last edited by a moderator:
