How to set the correct time.

Glanline · Dec 1, 2018

Hello ,

I would like to know about how to set the correct time.

My set up (Test set up time on LPS mode)

1. 13:00 A:0% B:1% C:1% D:1% E:0%
2. 14:00 A:10% B:01% C:10% D:1% E:10%
3. 15:30 A8:0% B:80% C:30% D:80% E:45%
4. 17:00 A:95% B:95% C:95% D:85% E:95%
5. 23.00 A:10% B:10% C:10% D:10% E:10%
6. 00.00 A:1% B:1% C:1% D:1% E:1%
7. 00:15 A:0% B:0% C:0% D:0% E:0%

1-4 the light running correct , but when the light running to 23:00 the light is automatic turn off that should be 00:15
After that i try to set it again at 23.15 (time on controller) i set number 6 all channel to 100% wait 20 sec the light still off why not open

For my question

How do can i set program correct .

Thank you.

noopsyche · Dec 1, 2018

Point Time A White B Blue C Royal Blue D UV E ERed Green
1 00:00 1% 1% 1% 1% 1%
2 00:15 0% 0% 0% 0% 0%
3 13:00 0% 1% 1% 1% 0%
4 14:00 10% 10% 10% 10% 10%
5 15:30 80% 80% 30% 80% 45%
6 17:00 95% 95% 95% 85% 95%
7 23:00 10% 10% 10% 10% 10%
1-7 group time must be set from small to large to 00:00 minimum

The B/C/D group starts to light up at around 6 o'clock. The brightness of 1% cannot be changed. Is it luminous? (If the light brightness setting of 13:00 B/C/D is 50%, the B/C/D light will change from 00:15 and then turn to 13:00 to set the brightness of the light)

noopsyche · Dec 2, 2018

Glanline said:
Hello ,

I would like to know about how to set the correct time.

My set up (Test set up time on LPS mode)

1. 13:00 A:0% B:1% C:1% D:1% E:0%
2. 14:00 A:10% B:01% C:10% D:1% E:10%
3. 15:30 A8:0% B:80% C:30% D:80% E:45%
4. 17:00 A:95% B:95% C:95% D:85% E:95%
5. 23.00 A:10% B:10% C:10% D:10% E:10%
6. 00.00 A:1% B:1% C:1% D:1% E:1%
7. 00:15 A:0% B:0% C:0% D:0% E:0%

1-4 the light running correct , but when the light running to 23:00 the light is automatic turn off that should be 00:15
After that i try to set it again at 23.15 (time on controller) i set number 6 all channel to 100% wait 20 sec the light still off why not open

For my question

How do can i set program correct .

Thank you.

Hello, the light's correct set must be from the earliest time to start setting.（From the earliest time A to G）

As shown：

I don't know if my explanation is clear enough. If you have another questions, I will try my best to answer you.

Glanline · Dec 3, 2018

noopsyche said:
Hello, the light's correct set must be from the earliest time to start setting.（From the earliest time A to G）

As shown：

I don't know if my explanation is clear enough. If you have another questions, I will try my best to answer you.

Thank you so much.

I will follow your set up and update the growth of my coral with K7

noopsyche · Dec 3, 2018

Glanline said:
Thank you so much.

I will follow your set up and update the growth of my coral with K7

Okay, looking forward to your coral growth record and beauty tank.

Glanline · Dec 5, 2018

Hello

For controller how long can a battery last?

Thank you.

noopsyche · Dec 5, 2018

Glanline said:
Hello

For controller how long can a battery last?

Thank you.

Hi
The controller is designed to be plugged into a power source and has a spare battery to allow the user to adjust the full box illumination within 6m. It can run for five to six hours to light up or standby for about thirty hours long.

Glanline · Dec 7, 2018

I have another problem when the power fails. The system will return to default. Number 1 . How do can i fix it?

Thank you

noopsyche · Dec 7, 2018

The controller should be used with power on, even it's power off, it will save the data, instead of returning to default status after power off

This is the modes conducting now, may we know where did you see the Number 1

Glanline · Dec 7, 2018

You mean the default state. Before the electricity will failure?

But I mean when the electricity comes back to normal. The program does not move forward, but returns to point 1.
This event occurs around 17.30 then came back to nomal at 17.35 program should be run on point 4 but back to point 1 .

I'm sorry for not fully explaining.

noopsyche · Dec 9, 2018

Glanline said:
I have another problem when the power fails. The system will return to default. Number 1 . How do can i fix it?

Thank you

Hi, Can you show your controller version and light fixture code to us.
PS: There is a small hole on the left side of the controller. You can insert a small tool into the hole to view the controller version. The picture will show you how to view the version of the controller.

noopsyche · Dec 9, 2018

Glanline said:
You mean the default state. Before the electricity will failure?

But I mean when the electricity comes back to normal. The program does not move forward, but returns to point 1.
This event occurs around 17.30 then came back to nomal at 17.35 program should be run on point 4 but back to point 1 .

I'm sorry for not fully explaining.

Can you give your e-mail to us? We will send you the software and controller program, you can fix it.