programming apex

  1. espinobj

    Apex RoDi Auto flush code

    I'm doing a big upgrade to my RODI setup. Im adding three additional solenoids. The main solenoid (RODIswitch) is existing and used as a on/off switch. There is a leak sensor labeled "GarageLK" and will work as a master shut off. Each of my storage containers have a high and low optical sensor -...
  2. espinobj

    Apex RoDi Auto flush code

    DELETE somehow posted twice
  3. s_tooz_123

    Apex programming for hysteresis functionality

    I have an ozone generator plugged into one of my EB832 ports. I currently have it programmed to turn on below 300: Fallback OFF Set OFF If ORP < 300 Then ON While the above keeps very tight control over the ORP, it causes frequent cycling of the EB832 port because it turns on at 299 and off at...
  4. B

    Having issue with Ph probe with Apex Classic

    Hi all this is my first post of rtr, recently I acquired a good priced apex classic and decided to jump on the good deal. Bought a new probe connected everything up and the apex does not even register that it will work with a ph probe. My apex fusion does not even have an imput section and when...
  5. Ditto

    Programing/Features Differences(Heater Setup – Part 2) – Neptune Systems and GHL Systems Controller

    This video is part two of a two-part video showing the Programing and Feature differences in programming and features for a heater for for both the APEX controller and a ProfiLux Controller. The first part of the video can be located here...
  6. Neptune Apex Programming Tutorials Part 8 and Conclusion: Lunar Schedule and Lighting Profiles

    Neptune Apex Programming Tutorials Part 8 and Conclusion: Lunar Schedule and Lighting Profiles

    This article is Part 8 of a series. Reef2Reef is extremely grateful to @SuncrestReef for sharing his expertise with us. These articles were badly needed and have been happily received by the Reef2Reef readership. Here is a quick Table of Contents for all the articles: Part 1 Introduction Part...
  7. Neptune Apex Programming Tutorials, Part 6: Alarms

    Neptune Apex Programming Tutorials, Part 6: Alarms

    This article is Part 6 of a series. Here is a quick Table of Contents for all the articles: Part 1 Introduction Part 2 Timers Part 3 Automatic Top-Off Kit (ATK) Part 4 Power Monitoring Part 5 Virtual Outputs Part 6 Alarms Part 7 Feed Cycles Part 8 Lunar Schedule and Lighting Profiles...
  8. Neptune Apex Programming Tutorials, Part 5: Virtual Outputs

    Neptune Apex Programming Tutorials, Part 5: Virtual Outputs

    Note From the Editor: This article is Part 5 of a series. Here is a quick Table of Contents for all the articles: Part 1 Introduction Part 2 Timers Part 3 Automatic Top-Off Kit (ATK) Part 4 Power Monitoring Part 5 Virtual Outputs Part 6 Alarms Part 7 Feed Cycles Part 8 Lunar Schedule and...
  9. Neptune Apex Programming Tutorials, Part 3: Automatic Top-Off Kit (ATK)

    Neptune Apex Programming Tutorials, Part 3: Automatic Top-Off Kit (ATK)

    For Inspiration: A beautiful 15-liter reef tank. This photo is from the Reef2Reef archives courtesy of @Fletch10_uk ©2019, All Rights Reserved. Note From the Editor: This article is Part 3 of a series. Here is a quick Table of Contents for all the articles: Part 1 Introduction Part 2 Timers...
  10. Neptune Apex Programming Tutorials Part 1

    Neptune Apex Programming Tutorials Part 1

    Note From the Editor: All of the articles in this series by the same author were originally part of several presentations made to a local aquarium club on programming your Neptune Apex Controller. The article is reprinted with permission from the author. Because this topic will be of great...
FM
Back
Top