programming

  1. CayoHueso

    How to set input "Low/High Point" on advanced outputs w/Hydros?

    What's the proper way to set the Low/High Point on an advanced output in the Hydros controller app? I'm setting up my new Hydros controllers, the XP8 and X3. I'm running the latest firmware, 342. It appears that the firmware has updated the layout of the outputs page in the last few months...
  2. TinyFish

    Help with Adaptive reef 4-way power box

    I recently bought a Adaptive reef 6-way power box second hand without a manual and iv'e no clue how to get it to work. Im trying to connect it to my apex and get it to control feed modes. I'm not worried about the programming piece but i can't seem to find the actual place to put said code. I...
  3. R

    GHL help with programming off function

    Hi, anyone able to help me out please. I Want to setup ozone to go off, if redox hits a set level and also turn off it the skimmer is switched off. Any help would be great  
  4. M

    Gyre xf300 advanced controller

    I’ve watched and read everything I can find about programming this new controller (latest/greatest w lcd screen). Can’t find anything with easy to follow instructions. Is this thing really just that ridiculously un-user friendly?! Hoping to set up 2 opposing xf350s with an alternating gyre that...
  5. S

    Using APEX DOS system as continuous feeding system 24hrs

    Hi there, I'm currently having some clogging problems with one of my feed vessels (I'm experimenting using different feed stocks) so I'm trying to feed my tank every minute 24/7. I have been able to program my APEX pump to feed every minute using the Feed system, however I can't appear to find...
  6. J

    programming pump to come on during 1 hour window only

    I must be missing something. I want my ATO pump to only be available to turn on for 1 hour per day (0700 - 0800). Even if the conditions to turn on the pump (eg. optical switch open) are met outside of that 1 hour window, I dont want it to come on. therefore, I have Fallback OFF Set OFF If...
  7. ariellemermaid

    ATK/ATO Failure Failsafe Coding Help

    For some time I’ve had a time-limited failsafe on my ATK/ATO. Under the ATO pump I’m using “When On > 004:00 Then OFF”. My ATO under normal conditions would never run for 4 minutes straight. Additionally, it usually runs every hour FYI. The problem is that the When command permanently turns the...
  8. R

    GHL Programmable logic

    I've been scratching my head and just can't figure out how to implement the following logic on my Profilux 4 I have 2 maintenance routines: 1) Water change: I turn most of the switches off, including skimmer and ATO pump 2) Filter floss change: Turn skimmer and ATO pump off only When...
  9. M

    Inkbird Failure with Apex Redundancy

    I have an Inkbird 306A controlling two 150w heaters. Occasionally the Inkbird will show an "Abnormal" alarm (at normal temperature-78F) and will cut power to the heaters, which can drop the temp of my tank about 2-degrees F overnight. The only way to reset the Inkbird's alarm is by cycling the...
  10. spacedcowboy

    NSW mixing and apex programming

    Having not seen any response to my post on Neptune's own forums I thought I'd post here and ask :) I'm thinking about buying another Apex to control my NSW supply, now that I'm thinking of mixing it myself again. My setup has two 300G NSW tanks, unfortunately at the other end of the house to...
  11. psumms

    Apex Multiple DOW + Time statements on same outlet

    Is it possible to have multiple time + day statements on an outlet, e.g. as below, testing this seems to suggest not. Is there a workaround? If Time 00:00 to 08:50 Then OFF If DOW ----TFS Then OFF If Time 08:53 to 14:50 Then OFF If DOW SMT---- Then OFF
  12. C

    Question on programming multiple solenoids (using profilux 4 and GHL powerbar)

    I have some programming questions. I am thinking of improving my RODI unit. I am thinking of buying 3 more solenoid valves to plug into my GHL powerbar. I already have one solenoid that turns on when my auto top off water bin is low. It is connected to two float switches. My solenoid...
  13. psumms

    APEX Programming - OFF > ON for 5 minutes then OFF

    THought I was pretty good with my APEX knowledge, for some reason I can't get my head around this one! I need an outlet OFF then when RO-CONTROL comes on, to have the outlet come on for four minutes then OFF. Simple! No problem if the SET is ON but I need the socket to be OFF for the all by...
  14. V

    HELP! Program and Install Apex with ATK and Icecap Kalk stirrer.

    Hello all, and thanks for stopping in to read and help if possible. Just installed my first apex and I have most of it figured out, but The Kalk stirrer and solenoid valve programming is starting to scare me. I had to run my top off line through a couple of walls, so adding a second line and...
  15. NewYorkReefer1988

    Neptune Apex Programming of BRS Dosers

    Hello all, I just finally took the plunge into the world of apex and I’m so glad I did. It is a lot to take in However. I am currently having a little bit of trouble programming my dosing pumps and corresponding powerhead in my sump. I actually think I have the dosing figured out but I will...
  16. psumms

    Apex Time spanning midnight

    Am i correct in thinking that the Apex time command cannot span midnight, so the following would not be valid: If Time 22:00 to 07:00 Then OFF and instead you would need to use two separate lines, e.g. If Time 22:00 to 23:59 Then OFF If Time 00:00 to 07:00 Then OFF Also, bonus question, does...
  17. psumms

    Apex programming - Two OSC on one socket

    Hi all, I have my RO unit flush for 30 seconds every four hours. I want to increase that to every 30 minutes when my RO pump is running. I currently have the following on my RO pump socket: Fallback ON OSC 000:00/000:30/180:00 Then ON What i'd like to do is find a solution to add a second line...
  18. PaulB777

    Apex with Trident - Outlet Programming Based on Test Values

    I have an Apex controller with a new Trident that I just got set up. My intention is to add a dosing system using the Bulk Reef Supply (BRS) 2 Part Doser Pumps. I'm pretty sure that I know how to program an outlet on the Apex to schedule the pump to turn on based on a time parameter (e.g. run...
  19. psumms

    Neptune Virtual Socket OFF after x minutes

    Hi all, I have a Virtual Socket that runs an MP40 Nutrient Export profile, looking to have this automatically switch to off after five minutes. I though the following should work, but seems not... Fallback OFF When On > 005:00 Then OFF
  20. Andrew Schubert

    Need Help setting my Alert Configuration for High Water ???

    I want my alert to go off if my High Water Float is activated. However, I do not want it to alert me if the ReturnPump is currently off (feeding my fish). Here is my current code: Set OFF If HWater OPEN Then ON If FeedA 011 Then OFF If FeedB 011 Then OFF If FeedC 011 Then OFF If FeedD 011 Then...
  21. Haubfather07

    Alert for inputs NOT changing

    I had a thought today that it would be nice to get an alert if a probe was having an issue by getting an alert that a reading WASN'T changing. A simple example of this would be temp. There is really only two options, the heaters are on and its climbing or off and its cooling. If my probe is...
  22. Wrasse-cal

    Gyre and Apex: won't run on "auto"

    I am having a problem figuring out how to correctly set up my XF-230 gyre via the Icecap Interface Module with my Apex. I have the gyre connected to the interface module, the gyre power supply plugged into the EB832 and the interface module connected to a variable speed port. The interface...
  23. Crabs McJones

    Disregard. Please close thread.

    Disregard. Mods please close thread.
  24. LEOreefer

    Mp10 with apex help

    So I just set up my wxm with my mp10. I was wondering if there was somewhere I could download daily programs into the setting? Kind of like how you could d/l preset programs for the ai light right into the app
  25. LEOreefer

    Mp10 with apex help

    So I just set up my wxm with my mp10. I was wondering if there was somewhere I could download daily programs into the setting? Kind of like how you could d/l preset programs for the ai light right into the app
Back
Top