I just finally finished setting up my 65g and turned the pump on for the first time. I noticed the flow seemed really loud so I looked in the corner-flow section where the noise was coming from. It turns out that there’s a hole on the underside of the elbow that my loc line is connected to, and...
I drilled my return line a little too high. I have a rimmed tank and the nut side of the bulkhead hits the trim so I can get it flush to the glass. Any ideas on how to remedy this?
Approximately 9 years old. Good condition. Includes stand, plumbing (manifolld) and cover. Located west Chicago suburbs.
Small Crack in front corner from original delivery (cosmetic only).
$850
900
Hey there. So I am getting back into the hobby after 40 years away. So much has changed. I have been using the BRS Facebook group and sharing my new build. I plan on doing a build thread here but before I get to that I need some advice. My display tank is a 60 gallon custom tank and I have built...
We are upgrading our reef tank from 90 to 120 and went with the seapora 120 long. We want to go with the wet/dry and don't have 30 Inches clearance as the store said we needed. We talked about just running the tubing up the backside and over the top of the aquarium how we have done years ago...
I have just completed the daunting task of drilling 2 holes in my 30G. Consists of two 3/4 inch bulkheads that lead to two 5/8 inch hoses. Connected everything to the sump and turned everything on. After adjusting everything to make sure the water level is just right I am hearing intermittent...
Hello everyone,
I need some guidance here.
I have a 30G DT with a 10G Sump I have just finished setting up. I was going to use a HOB overflow but have heard horror stories and with my work schedule I DO NOT want to risk a flood. So I will be pulling most of the water out my tank and moving live...
I am wondering what would be best for my 180 gallon bowfront. It is drilled for a single corner overflow but I wanted to either add a second overflow in the other corner or fill the holes (they are drilled at the back) and redrill for a ghost overflow.
What would be best?
Has anyone filled...
I believe the tank I’m wanting to drill is glass. Says the computer and polarized sunglasses test. My question is I’m trying to do an animal bean overflow on a 29 gallon. It is a standard aquarium with rim. How low should i drill the 3 holes. Trying to do what is below. Amya dice will be greatly...
Hi all! I’m getting back into the hobby! Even though the 13.5 is an AIO, I wanted to add a sump for additional water volume and filtration. I had a couple of 10 gallons hanging around so I set one up with an Amazon sump baffle kit. I looked into all kinds of over-glass U-shaped siphon designs...
Hello, I currently have a fully setup 80 Gallon Reef Ready setup that I would like to sell complete if possible. Tank Dimensions are 48" LG X 24" W X 16" T. The stand is homemade and 6' LG. I have 2 Kessil A360WE's setup for lights with goosenecks and a spectral controller. I also have a full...
Hey! So I got into saltwater a little over a month ago and I got the fluval evo. I love the size and look of the tank and it’s the perfect size for me as it fits on my nightstand. As I did more and more research I learned it’s much easier to have a higher water volume so I considered adding a...
Hey guys!
I’m going to try to make this as short as possible. I just recently purchased my first house and I’m in the process of moving my reef tank here. I’m currently using a 40 gallon breeder with a Fiji cube aio internal sump (similar to the Fluval evo). My neighbor gave me his old 75...
Hey all! Been a while since I posted. I just got a free 72 Gallon aquarium that I’m currently testing for leaks as I type. I was given the sump and protein skimmer as well but I have no knowledge as to how it was previously set up.
plumbing isn’t really my concerns as to how this skimmer works...